Hunter 40135 Manual

1Electronic/MechanicalThermostatModel 40135installation andoperation manual44017-01 04-01-2008

10If your existingthermostat is marked...label the wirewith this sticker:RH / R / VR / 4RHRH24 VoltRC / VCRCRC24 Volt CoolY / C* / MYYair conditioning

114. Using the provided stickers, label each wire according to the chart. (If the terminals are not labeled, contact a qualied HVAC

12INSTALLING THE THERMOSTATINSTALLING THE THERMOSTAT1. Remove the new thermostat from the back plate by pulling the two halves apart. ThermostatWall P

13WRCYG

142. Position the new wall plate on the wall and pull the labeled wires through the opening. 3. If the existing holes do not match those on the Hunter

15RCRHYGW

16INSTALLING THE THERMOSTAT, CONT.CONNECTING THE WIRES1. Loosen, but do not remove, the terminal screws. Note: A jumper wire has been provided, connec

17HE/HG Switch

18ATTACHING THE THERMOSTAT4. Locate the HE/HG s w i t c H on the back of the thermostat. Set the switch to HG for a gas furnace or oil burner. Set th

19

2Our Technical Support Group is available from 8 am to 5 pm CST. They may be reached toll-free at 1-888-830-1326.

20Fan SwitchSystem SwitchSet TemperatureSliderThermometerBattery IndicatorSYSTEMCOOLOFFHEATAUTOON3020109080706050FC9080706050F

21OPERATION1. Set the sE t tE m p E r a t u r E s l i d E r to the desired temperature. 2. The sy s t E m sw i t c H determines the operating mod

22INDICATORS AND ADUSTMENT1. The tH E r m o m E t E r indicates the room temperature.2. The Ba t t E r y in d i c a t o r displays two stages of ba

23Span AdjustSPAN

24INDICATORS AND ADJUSTMENTS, CONT.1. Remove the top cover from the thermostat. 2. To make your system run LONGER, turn the sp a n ad j u s t clockw

251. My heating or cooling will not turn on or off. 1 a. Check the HE/HG switch to ensure it is set to the correct position. 1 b. Wait. There may be a

26Is there help on the web? Yes. Visit http://www.hunterfan.com for more information. ...

27GRhWYF a n Rela yHea t/Cool24 V S u pplyCoolConta c torHea t Rela yor Valv e4-wire Hea t/Cool S ys t emGRcRhFan RelayHea t24V SupplyWHea t Relayor

28WIRING DIAGRAMSRhWHeat 24V orMillivo lt Su pplyHea t Rela yorValv e2-wire Hea t Only Sys temGRhWHea t 2 4 V S u pplyHea t Rela yorV alv e3-wire He

29GRcYCoolContacte rCool 2 4V Su pply3-wire Cool Only Sy s t emF a nRela yWIRING DIAGRAMS, CONT.

3Table of ContentsImportant Information ... 5Tools ...

30© 2007 Hunter Fan Company

4Congratulations!Thank you for choosing a Hunter thermostat. Your new Hunter thermostat will provide years of reliable service and year-round energy s

5This thermostat is designed to work on the followingheating and cooling systems:Gas – Standing PilotGas – Electronic IgnitionGas – Fired BoilersGas –

6This thermostat includes two #8 slotted screws and two wall anchors for mounting.To install your new thermostat, you will need the following supplies

7NOTICE! Do not disconnect the wires from the existing thermostat before reading these instructions. The wires must be labeled prior to removal to ens

8YRCGWYRCGW

91. Turn the system power OFF from the existing thermostat. Turn the power to the HVAC system OFF at the main power panel or at the furnace. 2. Remove