Hunter 53306 52 Meridale User Manual

www.HunterFan.com1.888.830.1326PAGE7PAGE13PAGE14PAGE10PAGE5PAGE18PAGE630 inches7 feetPAGE2What to Expect with Your InstallationCeiling BracketLadderPA

www.HunterFan.com1.888.830.1326WiringFROM FANFROM CEILING BRACKETFROM FANUsing an orange wire connector from the hardware bag, connect the 3 gr

www.HunterFan.com1.888.830.132611M3524-01 • 05/01/13 • © Hunter Fan CompanyCanopyLift the canopy into place so that the screw holes are aligned. Posit

www.HunterFan.com1.888.830.1326M3524-01 • 05/01/13 • © Hunter Fan CompanyBladesYour blades are shielded with Dust Armor® which is a nanotechnology coa

www.HunterFan.com1.888.830.1326Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and t

www.HunterFan.com1.888.830.1326Insert the socket ring into the inner glass as shown, then carefully place the inner glass inside the outer glass.Insta

www.HunterFan.com1.888.830.1326Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors

www.HunterFan.com1.888.830.1326Light Kit (continued)CONGRATULATIONS!YOU’RE DONE!Install a light bulb in each socket. Note: Do not use CFL bulbs to rep

www.HunterFan.com1.888.830.1326M3524-01 • 05/01/13 • © Hunter Fan Company17Maintenance & CleaningThe fan pull chain controls the speed: from high

www.HunterFan.com1.888.830.1326M3524-01 • 05/01/13 • © Hunter Fan Company18Troubleshooting Excessive wobbling• Tighten all of the blade and blade

www.HunterFan.com1.888.830.1326M3524-01 • 05/01/13 • © Hunter Fan CompanyWhat to Expect with Your InstallationKnow your wiringIf you are unfamiliar wi

Tools NeededLadderPower Drill (optional)9/64” Drill Bit (optional)ScrewdriversPliers Wire StrippersIf mounting to a support structure, you will also n

www.HunterFan.com1.888.830.13264M3524-01 • 05/01/13 • © Hunter Fan Company4If you have an angled ceiling:1. You will need a longer downrod (sold separ

1.888.830.1326www.HunterFan.comCeiling BracketOFFMake sure all four (4) bumpers are still attached.For angled ceilings, point opening toward peak.Refe

www.HunterFan.com1.888.830.1326Ceiling Bracket (continued)Preparation1.888.830.1326www.HunterFan.comDISCARDKEEP!Remove the shipping blocks from the mo

1.888.830.1326DownrodSlideSlide1 2 3 4 5678910Sold SeparatelyIncludedLonger Downrodfor angled ceilings or ceilings 10’ or higherShorterDownrodfor fans

KEEP!8”3/8”CUT& STRIP(not to scale)Remove the pre-installed setscrew so that the downrod can be inserted.Hand tighten the downrod (at least 4-5 fu

1.888.830.13269M3524-01 • 05/01/13 • © Hunter Fan Companywww.HunterFan.comDownrod (continued)DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the