Hunter 52006 Installation Guide

www.HunterFan.com1.888.830.1326Table of Contents?PAGE10WiringPAGE7DownrodPAGE6Preparation CanopyPAGE11PAGE5Ceiling BracketMounting OptionsPAGE430 inch

www.HunterFan.com1.888.830.1326WiringTurn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the w

www.HunterFan.com1.888.830.1326CanopyLift the canopy into place so that the screw holes are aligned. Position the canopy so that, when lifted into pla

www.HunterFan.com1.888.830.1326BladesYour blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fa

www.HunterFan.com1.888.830.1326Switch HousingFeed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around th

www.HunterFan.com1.888.830.132614M0065-01 • 05/13/14 • © Hunter Fan CompanyConnect the plugs from the upper and lower switch housings. Make sure to li

www.HunterFan.com1.888.830.1326Light Kit (continued)Note: Glass shade style and number of lights may vary.Install a bulb into each of the sockets. Whe

www.HunterFan.com1.888.830.1326Remote ControlNote: The remote must be paired before the fan will operate.Within 3 minutes of restoring power to the fa

www.HunterFan.com1.888.830.1326Remote Control (continued)Light ButtonPush the light button on the remote transmitter. Pull the light chain once. If th

www.HunterFan.com1.888.830.1326Rocker- Style PlateSwitch Cover PlateRemoved TabsTo install the transmitter cradle, remove the two screws holding the s

www.HunterFan.com1.888.830.1326For questions regarding removing a light kit, call customer service 1-888-830-1326.Operation, Maintenance, & Cleani

www.HunterFan.com1.888.830.1326M0065-01 • 05/13/14 • © Hunter Fan Company1.888.830.13261.888.830.1326What to Expect with Your InstallationKnow your wi

www.HunterFan.com1.888.830.1326Troubleshooting Fan doesn’t work• Make sure power switch is on.• Pull the pull chain to make sure it is on.• Push

www.HunterFan.com1.888.830.13263M0065-01 • 05/13/14 • © Hunter Fan CompanyTools NeededLadderPower Drill (optional)9/64” Drill Bit (optional)Screwdrive

www.HunterFan.com1.888.830.13264M0065-01 • 05/13/14 • © Hunter Fan CompanyMounting Options (continued)If you have an angled ceiling:1. You will need a

www.HunterFan.com1.888.830.1326Ceiling BracketRefer to warning w.1 on pg. 2To avoid possible electrical shock, before installing your fan, disconnect

www.HunterFan.com1.888.830.1326PreparationDISCARDKEEP!Remove the shipping blocks from the motor. Save the screws. They will be needed for blade iron i

www.HunterFan.com1.888.830.13267M0065-01 • 05/13/14 • © Hunter Fan CompanyDownrodSlideSlide1 2 3 4 5678910Sold SeparatelyIncludedLonger Downrodfor ang

www.HunterFan.com1.888.830.13268M0065-01 • 05/13/14 • © Hunter Fan CompanyKEEP!8”3/8”CUT& STRIP(not to scale)Remove the pre-installed setscrew so

www.HunterFan.com1.888.830.1326Downrod (continued)DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling b