145072-01 • 10/21/10 • Hunter Fan Company1 • Getting Ready ...
1045072-01 • 10/21/10 • Hunter Fan Company104 • Setting the Remote Transmitter and Receiver4 • Setting the Remote Transmitter and Receiver8786e D
1145072-01 • 10/21/10 • Hunter Fan Company114 • Setting the Remote Transmitter and Receiver(cont.)8726487Install the included 12-Volt, type GP23A
1245072-01 • 10/21/10 • Hunter Fan Company125 • Wiring the Fan70705.1WARNING!: All wiring must be in accordance with national and local electrical
1345072-01 • 10/21/10 • Hunter Fan Company135 • Wiring the Fan5.35.25.4Using the large wire connectors (70), connect the white wire and the black
1445072-01 • 10/21/10 • Hunter Fan Company146 • Installing the Ceiling Plate CoverPartially install (about 2 full turns) two canopy screws (62) in
1545072-01 • 10/21/10 • Hunter Fan Company157 • Assembling the BladesAttach each blade (46) to a blade iron (44) using three blade assembly screws
1645072-01 • 10/21/10 • Hunter Fan Company16Note: After the retaining screws are removed, the blades will feel loose. is is normal, as loose blad
1745072-01 • 10/21/10 • Hunter Fan Company179 • Completing Your Installation With a Bowl Light Fixture696930309.29.19.3Partially install two inner
1845072-01 • 10/21/10 • Hunter Fan Company18Note: Both plug connectors are polarized and will only t together one way. Make sure the connectors a
1945072-01 • 10/21/10 • Hunter Fan Company199.109.119.9115150149Place the cover plate (148) up against the glass bowl (150). Align the holes in th
245072-01 • 10/21/10 • Hunter Fan Company• READ AND SAVE THESE INSTRUCTIONS.• Use only Hunter replacement parts.• To reduce the risk of persona
2045072-01 • 10/21/10 • Hunter Fan Company2010.2Remove the nut and washer from inside the center of the lower switch housing (31).After your insta
2145072-01 • 10/21/10 • Hunter Fan Company21Removing the Light Fixture10.6Install the switch housing cap (255) and screws (245) to the lower switc
2245072-01 • 10/21/10 • Hunter Fan CompanyTroubleshootingProblem: Nothing happens; fan does not move.1. Turn power on, replace fuse, or reset br
2345072-01 • 10/21/10 • Hunter Fan CompanyWinterUpward AirflowClockwiseSummerDownward AirflowCounterclockwiseAirflow DirectionCeiling fans work best
345072-01 • 10/21/10 • Hunter Fan Company1 • Getting Ready (continued)7 feet Minimum Blades to Floor 8 feet Minimum Ceiling Height30 in. From Wall
445072-01 • 10/21/10 • Hunter Fan Company1 • Getting Ready (continued) CAUTION: All wiring must be inaccordance with national and local electrical
545072-01 • 10/21/10 • Hunter Fan Company52.22.42.12.32 • Installing the Ceiling Mounting Plate7122Your ceiling mounting plate (2) comes with four
645072-01 • 10/21/10 • Hunter Fan Company6Note: e isolators must be ush against the ceiling. A loose ceiling mounting plate will result in impro
745072-01 • 10/21/10 • Hunter Fan Company7You can assemble your fan for standard or angled mounting as shown in steps 3-1 – 3-3. For low prole mo
845072-01 • 10/21/10 • Hunter Fan Company83 • Assembling and Hanging the Fan3.53.73.43.6Raise the fan and place the hook on the hanger bracket (2)
945072-01 • 10/21/10 • Hunter Fan Company9Remove the pin from the pipe, then slide the wedge o the pipe.Remove the pipe ball screw from the stand
Comments to this Manuals